MODEL 809 9MM PISTOL IN BLACK TENNIFER

MODEL 809 9MM PISTOL IN BLACK TENNIFER

4 Comments

3 years 26 weeks ago, 12:28 PM

luckybychoice

luckybychoice's picture


Rank:
Secretary of the Treasury
Points:
6791
Join Date:
May 2009
Location:
United States
I just went to

a gunstore here at lunch time,high prices on everthing compared to online,wtf,they were selling used guns for 20 bucks less than new,i was dissapointed,BTW,this is a nice looking Taurus.

i tried being reasonable,i didn't like it, NRA LIFE MEMBER,USMC VETERAN
3 years 26 weeks ago, 12:40 PM

Ishootdaily

Ishootdaily's picture

Rank:
General
Points:
4375
Join Date:
Feb 2009
Location:
Saint Petersburg, Florida, United States
809 Taurus

I'm going to be doing a trigger and action job on one of these for one of the elderly shooters down at the range.

One Eye Bob, yes he only has one eye... lol

Anyway, he has one and he asked me to shoot it a while back, shot very good but the tigger was a bit chunky.

So now I guess I'm to polish up the action and see about getting the trigger a little lighter for him.

No sir, he fell into that bullet... Never argue with a stupid person. They'll just drag you down to their level and beat you with experience!!
3 years 26 weeks ago, 12:50 PM

luckybychoice

luckybychoice's picture


Rank:
Secretary of the Treasury
Points:
6791
Join Date:
May 2009
Location:
United States
so how many rounds

did/do you run thru before you decide to do a polish job? i ran into an issue with my Dan Wesson .44mag revolver a few years ago,stacking on certain cylinders but not others,even after 600-800 rounds.A trip to the gunsmith for an action job solved the issue( DW gunsmith).I had an AMT backup in .380 that liked to stack too.

i tried being reasonable,i didn't like it, NRA LIFE MEMBER,USMC VETERAN
3 years 26 weeks ago, 1:19 PM

Ishootdaily

Ishootdaily's picture

Rank:
General
Points:
4375
Join Date:
Feb 2009
Location:
Saint Petersburg, Florida, United States

I tear a weapon down as soon as I get it home the first time and go through it. For the most part I use a piece of leather stretch over a 12x12 plate glass I cut out of a Window a few years back. I've rubbed Jewelers Polish into it over the years and I'll Lap all flat surfaces on that for a light polish job. I use lapping paste on another sheet of glass for heavy tooling marks and cutting where needed if there is any extra material causing a moving part to hang, bounce. Though not all extra material should be removed all the time. On the CZ with the internal rails running the full length of the frame and slide you can find extra material on the slide rail. It actually might mess with the fitting of the slide and frame if the extra material is removed without first checking it out.

As far as breaking it in goes, you can and it would probably be better to do that first to ensure you do not remove material that should stay.

On the Dan Wesson, was it the Cylinder or the Hand causing it to hang?

I know that on some of the 38 cal S&W revolvers if you get even a piece/small clump of burnt powder in between the transfer bar and the cylinder notch it will not seat correctly and will hang though the hammer will function.

No sir, he fell into that bullet... Never argue with a stupid person. They'll just drag you down to their level and beat you with experience!!
sytasyn_syn's picture
Posted by: sytasyn_syn
3 years 26 weeks ago
Views:
2,302
Comments:
4
Association:
Taurus 800 series

Rating Overview

This text will be replaced

Suggestions

Beretta 92
Diamondback 380
S&W 4506
Kel-Tec PMR 30
Smith & Wesson .40 cal, my Carry
Got a new little ditty for me and the Wife
Glock 21 with Magazine
Colt 1911
Beretta 92
Ruger MK III
Concealed Carry Works
Arsenal Arms double bbl 1911 .45
Beretta 85f .380 Ambi controls, unfired
Glock 17
HK Pistol
Well said

Recent Activity